UK Trade Tariff
Heading 8481: Taps, cocks, valves and similar appliances for pipes, boiler shells, tanks, vats or the like, including pressure-reducing valves and thermostatically controlled valves
-
8481 10Pressure-reducing valves
-
8481 10 05Combined with filters or lubricators
- 8481 10 05 10For use in certain types of aircraftDuty & VAT →
- 8481 10 05 90OtherDuty & VAT →
-
8481 10 19Other
-
8481 10 19Of cast iron or of steel
- 8481 10 19 10For use in certain types of aircraftDuty & VAT →
- 8481 10 19 90OtherDuty & VAT →
-
8481 10 99Other
- 8481 10 99 10For use in certain types of aircraftDuty & VAT →
- 8481 10 99 40Pressure reducing valves in a brass case with:-a length of not more than 30 mm (± 1 mm),-a width of not more than 18 mm (± 1 mm),of a kind used for incorporation in fuel delivery modules of motor vehiclesDuty & VAT →
- 8481 10 99 90OtherDuty & VAT →
-
8481 20Valves for oleohydraulic or pneumatic transmissions
-
8481 20 10Valves for the control of oleohydraulic power transmission
- 8481 20 10 20For use in certain types of aircraftDuty & VAT →
- 8481 20 10 90OtherDuty & VAT →
-
8481 20 90Valves for the control of pneumatic power transmission
- 8481 20 90 20For use in certain types of aircraftDuty & VAT →
- 8481 20 90 90OtherDuty & VAT →
-
8481 30Check (non-return) valves
-
8481 30 91Of cast iron or of steel
- 8481 30 91 20For use in certain types of aircraftDuty & VAT →
-
8481 30 91 30Other
- 8481 30 91 30Mechanical check (non-return) valve for opening and closing of the flow of fuel:-with an operating pressure of not more than 250 mpa,-with a flow rate of 45 cm³/minute or more, but not more than 55 cm³/minute,-with 4 input holes, each of them with a diameter of 1.2 mm or more, but not more than 1.6 mm,-made of steelDuty & VAT →
- 8481 30 91 91Steel check (non-return) valves with:- an opening pressure of not more than 800 kpa- an external diameter not more than 37 mmDuty & VAT →
- 8481 30 91 99OtherDuty & VAT →
-
8481 30 99Other
- 8481 30 99 20For use in certain types of aircraftDuty & VAT →
- 8481 30 99 50Mechanical check (non-return) valve for opening and closing of the flow of fuel:-with an operating pressure of not more than 250 mpa,-with a flow rate of 45 cm³/minute or more, but not more than 55 cm³/minute,-with 4 input holes, each of them with a diameter of 1.2 mm or more, but not more than 1.6 mm,-made of steelDuty & VAT →
- 8481 30 99 90OtherDuty & VAT →
-
8481 40Safety or relief valves
-
8481 40 10Of cast iron or of steel
- 8481 40 10 50For use in certain types of aircraftDuty & VAT →
- 8481 40 10 90OtherDuty & VAT →
-
8481 40 90Other
- 8481 40 90 10For use in certain types of aircraftDuty & VAT →
- 8481 40 90 90OtherDuty & VAT →
-
8481 80Other appliances
-
8481 80 11Taps, cocks and valves for sinks, washbasins, bidets, water cisterns, baths and similar fixtures
-
8481 80 11Mixing valves
- 8481 80 11 10For use in certain types of aircraftDuty & VAT →
- 8481 80 11 90OtherDuty & VAT →
-
8481 80 19Other
- 8481 80 19 10For use in certain types of aircraftDuty & VAT →
- 8481 80 19 90OtherDuty & VAT →
-
8481 80 31Central heating radiator valves
- 8481 80 31 00Thermostatic valvesDuty & VAT →
- 8481 80 39 00OtherDuty & VAT →
-
8481 80 40Valves for pneumatic tyres and inner tubes
- 8481 80 40 10For use in certain types of aircraftDuty & VAT →
- 8481 80 40 90OtherDuty & VAT →
-
8481 80 51Other
-
8481 80 51Process control valves
- 8481 80 51 00Temperature regulatorsDuty & VAT →
-
8481 80 59Other
- 8481 80 59 20Pressure regulating valve for incorporation into compressors of motor vehicle air condition unitsDuty & VAT →
- 8481 80 59 30Two-way flow control valve with housing, with: - at least 5, but not more than 16 outlet holes with at least 0.05 mm, but not more than 0.5 mm diameter, - at least 330 cm³/minute, but not more than 5 000 cm³/minute flow rate, - at least 19, but not more than 300 mpa operating pressureDuty & VAT →
- 8481 80 59 40Flow-control valve- made of steel,- with an outlet hole with a diameter of at least 0.05mm or more, but not more than 0.5 mm,- with an inlet hole with a diameter of at least 0.1 mm, but not more than 1.3 mm,- with chromium nitride coating,- with a surface roughness of rp 0.4Duty & VAT →
- 8481 80 59 50Electromagnetic valve for quantity control with- a plunger,- a solenoid with a of coil resistance of at least 1.85 ohm, but not more than 8.2 ohmDuty & VAT →
- 8481 80 59 60Electromagnetic valve for quantity control- with a solenoid with a coil resistance of at least 0.19 ohm, but not more than 0.66 ohm, and with an inductance of not more than 1 mhDuty & VAT →
- 8481 80 59 70Flow-control valve-made of steel,-with an outlet hole with a diameter of at least 0.05 mm, but not more than 0.5 mm,-with an inlet hole with a diameter of at least 0.1 mm, but not more than 1.3 mmDuty & VAT →
- 8481 80 59 80Solenoid valve for combustion engine oil pump to regulate the quantity of oil in the pump:-with a cable of length of 550 mm or more but not more than 700 mm incorporating an electrical connector,-with an operating pressure of not more than 5.5 bar,-with an operating voltage of 9 vdc or more but not more than 16 vdc,-with a valve's base width of 22 mm or more but not more than 27 mm,-with a valve's length of 55 mm or more but not more than 110 mm,for use in the manufacture of motor vehicle enginesDuty & VAT →
- 8481 80 59 90OtherDuty & VAT →
-
8481 80 61Other
-
8481 80 61Gate valves
- 8481 80 61 00Of cast ironDuty & VAT →
-
8481 80 63Of steel
- 8481 80 63 50For use in certain types of aircraftDuty & VAT →
- 8481 80 63 90OtherDuty & VAT →
-
8481 80 69Other
- 8481 80 69 50For use in certain types of aircraftDuty & VAT →
-
8481 80 69 60Other
- 8481 80 69 60Four-way reversing valve for refrigerants, consisting of:- a solenoid pilot valve- a brass valve body including valve slider and copper connectionswith a working pressure up to 4.5 mpaDuty & VAT →
- 8481 80 69 99OtherDuty & VAT →
-
8481 80 71Globe valves
- 8481 80 71 00Of cast ironDuty & VAT →
-
8481 80 73Of steel
- 8481 80 73 10For use in certain types of aircraftDuty & VAT →
- 8481 80 73 20Pressure- and flow-control valve controlled by external electromagnet:- made of steel and/or steel alloy(s),- without integrated circuit,- of not more than 1000 kpa operating pressure,- with a flow quantity of not more than 5 l/min,- without an electromagnetDuty & VAT →
- 8481 80 73 90OtherDuty & VAT →
-
8481 80 79Other
- 8481 80 79 10For use in certain types of aircraftDuty & VAT →
- 8481 80 79 40Service valve which suits for r410a or r32 gas while connecting indoor and outdoor units with:-a withstanding pressure of the valve body of 6.3 mpa,-a leakage ratio of less than 1.6 g/a,-an impurity ratio of less than 1.2 mg/pcs,-an airtight pressure of the valve body of 4.2 mpafor use in the manufacture of air conditionersDuty & VAT →
- 8481 80 79 90OtherDuty & VAT →
-
8481 80 81Ball and plug valves
- 8481 80 81 30For use in certain types of aircraftDuty & VAT →
- 8481 80 81 90OtherDuty & VAT →
-
8481 80 85Butterfly valves
- 8481 80 85 30For use in certain types of aircraftDuty & VAT →
- 8481 80 85 90OtherDuty & VAT →
-
8481 80 87Diaphragm valves
- 8481 80 87 30For use in certain types of aircraftDuty & VAT →
- 8481 80 87 90OtherDuty & VAT →
-
8481 80 99Other
- 8481 80 99 40For use in certain types of aircraftDuty & VAT →
- 8481 80 99 70Pressure- and flow-control valve controlled by external electromagnet:- made of steel and/or steel alloy(s),- without integrated circuit,- of not more than 1000 kpa operating pressure,- with a flow quantity of not more than 5 l/min,- without an electromagnetDuty & VAT →
- 8481 80 99 80Solenoid valve for combustion engine continuous variable valve timing system to control oil flow as a function of engine speed and load:-in metal cover,-with electrical connector,-with a force of not more than 10 n,-with an operating voltage of 9 vdc or more but not more than 16 vdc,-with a length of 80 mm or more but not more than 110 mm,-with a width of 80 mm or more but not more than 110 mm,-with a height of 20 mm or more but not more than 30 mm,for use in the manufacture of engines of motor vehiclesDuty & VAT →
- 8481 80 99 90OtherDuty & VAT →
-
8481 90Parts
- 8481 90 00 10For use in certain types of aircraftDuty & VAT →
- 8481 90 00 25Die-cast aluminium housing for electronic throttle control or exhaust gas recirculation systems, comprising the following features:-high-pressure die-cast aluminium en ac-46000,-shot-blasted and machined,-height of 100 mm or more but not exceeding 135 mm,-width of 115 mm or more but not exceeding 150 mm,-weight of 210 g or more but not more than 500 gDuty & VAT →
- 8481 90 00 40Valve armature:- for the opening and closing of the flow of fuel,- consisting of a shaft and a blade,- with at least 3 but not more than 8 holes on the blade,- made of metal and/or metal alloy(s)Duty & VAT →
- 8481 90 00 50Silicone or plastic keyboards, comprising:-parts of common metal, and-whether or not comprising parts of plastic,-epoxy resin reinforced with fiberglass or wood,-whether or not printed or surface-treated,-with or without electrical conductors,-with or without a membrane bonded to the keyboard,-with or without mono or multilayer protective filmDuty & VAT →
- 8481 90 00 60Nozzle body for the regulation of angle and distribution of fuel injection:-of a cylindrical shape,-made of stainless steel,-with 4 or more, but not more than 16 holes,-with a flow rate of 100 cm³/minute or more, but not more than 500 cm³/minuteDuty & VAT →
- 8481 90 00 70Nozzle needle for opening and closing the flow of fuel in the engine, with:-2 holes,-4 grooves,-a diameter of 3 mm or more, but not more than 6 mm,-a length of 25 mm or more, but not more than 35 mm,-made of stainless steel with hard-chrome platingDuty & VAT →
- 8481 90 00 80Flow-control valve-made of steel,-with an outlet hole with a diameter of at least 0.05 mm, but not more than 0.5 mm,-with an inlet hole with a diameter of at least 0.1 mm, but not more than 1.3 mmDuty & VAT →
- 8481 90 00 90OtherDuty & VAT →